When we start to repair & replace an old CRT monitor from an machine,we need to know the video pinout definition to make the connection with out multisync to XVGA converter(HC1011).
Industrial Monitor Video Connectors:
There are different connectors for old generation industrial monitor, like 4pin, 7pin, 9pin, 14pin, 20pin, 24pin, 25pin, flat cable, 3BNC, 4BNC, YUV, Component etc.
Industrial Monitor Colors:
Most of the color industrial monitor use RGB signals, which include 3elements color Red(R), Green(G), Blue(B). How the RGB works, please check following link:
http://en.wikipedia.org/wiki/RGB_color_model
Monochome also can be produced by RGB.
How does an industrial monitor transmit the video singals?
-The display color was created of R,G,B colors. Hs and Vs control the Signal transmit method,include
RGB SOG (RGsyncB)
RGB SOB (RGBsync)
RGB SOR (RsyncGB)
RGB Sync (Composite sync)
RGB HV (Separate sync)
YPbPr (Component)
The testing methods to find out the video type of an industrial monitor:
-There are five different signals, R- G- B- H- V, need to be find out,(or there are four signal when in composite sync)
We introduce three ways to find out the RGBHV,
1. Judge by the color of wire.
Normally, R is Red wire, G is green wire, and B is blue wire; Hs is yellow wire, Vs is white wire. Metal case or black wire or shielding wire is GND.
2. Test by multimeter
- set the multimeter in resistance testing,
black wire of multimeter connect to GND, find the three wires which resistance at about 75ohm. They are RGB wires.
- Hs wire testing. please shift the multimeter to Frequency Testing. Connect the black wire of multimeter to GND,use the red wire of multimeter to find out the wire which frequency ranged at 15kHz - 90kHz.
- Vs wire testing. find out the wire which frequency ranged at 20Hz- 120Hz.
3.Test by oscilloscope
- wave form of R,G,B is irregular, the frequency jump and down substantially,similar as follows:
- Hs wave form similar as follows, frequency ranged at 15kHz - 90kHz
- Vs wave form similar as follow, frequency ranged at 20Hz - 120Hz,
For BNC connector, please test the resistance or frequency between the BNC metal casing and BNC core.
For further support, please contach engineer Mr.Sam
Industrial monitor include: RGB Industrial Monitor, MDA Industrial Monitor, CGA Industrial Monitor, Ega Industrial Monitor, mono industrial monitor and green industrial monitor. Because almost all automation control system uses analog singals, but the common PC monitor uses digital signal. So a pc monitor cannot apply to industrial use directly.This is one of the differece between a industial monitor with a general PC monitor. Secondly, the industrial monitor working enviroment is much worse compare to a general monitor. mostly, industrial monitor must dust proof, oil proof, and water proof, and with anti-shock ability. Many old industrial monitors from old generation automation after a longterm use, was broken, and need to be repaired or replaced by a new generation industrial lcd monitor.So we develop our new generation industial monitor with a scaler, which will converter the multisync analog signals to a standard vga signals.
|
© 2011 Hmwtech Co.,ltd. All Rights Reserved. Any enquiries, please email the webmaster at info@harmonywolrd.com.
english | ä¸æ–‡ | العربية | Française | Deutsch | Italiano | 日本ã®è¨€èªž | í•œêµì˜ | Português | руÑÑкий | Español | Türk |
Home | Industrial Monitor | PLC | AD Boards | TFT-LCD Modules | Contact Us | Sitemap |
xVGA Converter | 7 inch | 8-9 inch | 10-12 inch | 14-15 inch | 17 inch | 19 inch | By brands |
Powered by Hmwtech Co.,ltd |